Controls

HC20 wireless

The HC20 is a wireless handset control for advanced TWINDRIVE dual actuator systems in leisure beds. Comes with RF or Bluetooth communication. Ergonomic and user-friendly with backlit buttons and a flashlight function.

HC20 wireless

The Hand Control HC20 wireless is designed for control of leisure beds with TWINDRIVE® systems.

It has a contemporary design that matches the trend within interior design. The HC20 combines ergonomic design and functionality in a user-friendly hand control without an annoying cable. As standard the HC20 offers memory of favorite positions, backlighting in the buttons for extra user-friendliness and a flashlight function.

Gives you the option to control up to 4 channels or, e.g., the massage function in the bed system.

HC20 Wireless data sheet

View the data sheet as an online magazine or download the PDF.

TWINDRIVE TD4 Advanced user manual

This user manual will tell you how to install, use and maintain your LINAK TWINDRIVE products.

TWINDRIVE TD32 TD33 user manual

This user manual will tell you how to install, use, and maintain your LINAK TWINDRIVE products.

Expanding your comfort zone

When it comes to leisure beds, LINAK understands the need for safe and reliable actuator systems that work day after day. The TWINDRIVE system is the right system for bed manufacturers.

HOMELINE product overview

Explore the variety of TWINDRIVE systems with a low noise level and the small built-in dimensions used in both box spring beds and slatted beds.

TD4 quick guide - Pairing devices and mechanical lowering

Learn how it only takes a few steps to pair devices to the dual actuator TD4 using Bluetooth® technology or mechanically lower a comfort bed with TD4 in case of power shortages.

Assembling a single actuator system

How to assemble a single actuator system

The system consists of:
Single actuator(s)
1 x Switch Mode Power Supply
1 x CBH Advanced
1 x Bluetooth® hand control
1 x Bluetooth® Adapter

  1. Connect single actuators in channels 1-2 to control adjustment of, for example, backrest and leg support. (With the 3-ch CBH Advanced, the 3rd channel can also be used for an actuator)
  2. Plug the DC cable into the CBH Advanced
  3. Plug the Bluetooth® Adapter into the CBH Advanced
  4. Connect to a power outlet
  5. Pair the hand control (press the two top buttons simultaneously)
  6. The system is now ready for setup

Assembling a single actuator system with massage motors

How to assemble a single actuator system with massage motors

The system consists of:
Single actuator(s)
Massage motor(s)
1 x Switch Mode Power Supply
1 x CBH Advanced
1 x Bluetooth® hand control
1 x Bluetooth® Adapter

  1. Connect single actuators in channels 1-2 for, e.g., back and leg adjustment
  2. Connect massage motors in channels 3A and 3B
  3. Plug the 2-pole DC cable into the CBH Advanced
  4. Connect the other end of the cable to the SMPS and connect the cable
  5. Connect to a power outlet
  6. Plug the Bluetooth® Adapter into the CBH Advanced
  7. Pair the hand control
  8. The system is now paired and ready for use

How to pair wireless hand controls to a LA18 IC system for comfort beds

Learn how to pair wireless hand controls to the LINAK® single actuator LA18 IC system for comfort beds using Bluetooth® technology.

  1. Connect the system to a power outlet
  2. Pairing mode has started when the Under Bed Light starts flashing. It will run for 3 minutes
  3. Press the top two buttons to pair the hand control 
  4. A long flash means successful pairing
  5. The system is paired and ready for use
  6. The system will continue to be in pairing mode until the previously mentioned 3 minutes elapse. Then the light will turn green continuously to show that the system is no longer in pairing mode

How to store memory on a hand control

How to store memory on a hand control

  1. Adjust the bed to a preferred position
  2. Press S and then choose the number on which you want to store the position
  3. Now the position is stored
  4. When you want to return to this position later, simply press and hold the button on which you stored the position

Initializing a single actuator system

How to initialize a single actuator system

  1. Connect to a power outlet
  2. Actuators must be in the inner position
  3. Push the "down" button of the actuator on the hand control for approx. 5 seconds
  4. The actuator now initiates and can drive outwards
  5. Repeat this for each actuator by pressing the matching "down" button on the hand control
  6. The actuator system is now initialized

Buy a new LINAK hand control for an adjustable bed

If you need a new hand control for your adjustable bed, you need to contact the supplier from whom you purchased the bed. 
This applies both in cases where you have lost your hand control, the hand control is broken as well as in cases where the battery has run out of power and the battery cannot be exchanged. The supplier will assist you in ordering a new hand control - LINAK does not sell spare parts directly to the person who owns the bed.

The LINAK hand control for an adjustable bed does not work

The LINAK hand control for an adjustable bed does not work

If you experience problems with the hand control for your adjustable bed, you need to contact the supplier from whom you purchased the bed. 
LINAK does not sell spare parts directly to the person who owns the bed.

My neck function does not recall the correct memory function

The actuator adjusting the neck function needs to be initialized. Follow the instructions shown in the video or in the following steps:

My RF handset does not work

The handset needs to be set up with the TWINDRIVE TD1 280 (memory) underneath the bed.

Follow the instructions shown in the video or in the following steps:

  1. Activate the reset key on the RFR box attached to the TD1.
  2. Keep the reset key activated while pressing a random button on the handset. If there are more handsets, keep the reset key activated and press a random button on the other handset.
  3. Your bed is now ready for use.

Pairing hand controls to the CBH Advanced system with a Bluetooth® Adapter

How to pair hand controls to a system with a CBH Advanced and a Bluetooth® Adapter

  1. Connect to a power outlet  
  2. Bluetooth® Adapter flashes for 3 minutes to indicate pairing mode
  3. To pair a hand control, press the two top buttons while the adapter is flashing
  4. A long flash indicates successful pairing
  5. All LINAK hand controls are paired by pressing the two top buttons

How to pair a hand control later

  1. Start pairing mode again
  2. Unplug from the power outlet and wait 10 seconds
  3. Connect to a power outlet
  4. Bluetooth® Adapter flashes for 3 minutes to indicate pairing mode
  5. Repeat pairing procedure on the other hand control
  6. The system is now paired and ready to use
 

Parallel drive with the TD4/TD5 Advanced

How to connect a TD4/TD5 Advanced system and use parallel drive

The system consists of:
2 x TD4/TD5 Advanced
2 x Switch Mode Power Supply
1 x Serial cable
1 x Bluetooth® hand control 

  1. Connect 2 x SMPS to the 2 x TD4/TD5 Advanced
  2. Use one serial cable to connect the two TD4/TD5 Advanced
  3. Connect both actuators to a power outlet
  4. Pair the hand control
  5. The TD4/TD5 system will now run in parallel when using the hand control

TD1RF (with memory) and LA27 - how to initialize the motor system

  1. Drive the LA27 to the outer position (without interruption until it stops)
  2. Release the button
  3. Drive the LA27 to the inner position (without interruption until it stops)
  4. Release the button

The system has now been initialized.

TD3 - How to set up Bluetooth handsets

  1. Plug the Bluetooth Adapter into the powered up TD3.
  2. The Adapter is now in pairing mode. A blue blinking LED will indicate this.
  3. Take the Bluetooth hand control and press the Back “Up” and “Down” buttons at the same time. Now the light will display a long blink and indicate that the control and the actuator are paired up.

TD3 - How to set up radio frequency handsets

  1. Activate the reset key on the TD3. The bed drives to a flat position. Keep the key pressed until the motor stops completely.
  2. Release the reset key.
  3. Reactivate the reset key on the TD3.
  4. Keep the reset key activated while pressing a random button on the handset.
  5. If there are more handsets, keep the reset key activated and press a random button on the other handset.

Your bed is now ready for use.

TD4 - How to set up a Bluetooth handset

  1. Set the TD4 in pairing mode by connecting it to a power outlet.
  2. The product is now in pairing mode. The Under Bed Light will blink to indicate this.
  3. Take the Bluetooth hand control and press the Back “Up” and “Down” buttons at the same time. Now the light will display a long blink and indicate that the control and the actuator are paired up.
 

The bed does not work at all (TD1)

Check: Is the power outlet connected to the TWINDRIVE TD1?
Try/Solution: Try to connect a lamp or a similar object to the power outlet to check that the supply voltage is OK.

Check: Are all plugs mounted correctly on the TWINDRIVE TD1?
Try/Solution: Check all connections.

Check: Is there any visible damage to the cables?
Try/Solution: Damaged parts must be exchanged. Contact the company that sold you the bed.

The bed does not work at all (TD3)

Check: Is the power line connected to the TWINDRIVE TD3?

Try/Solution: Try to connect a lamp or similar to the power outlet to check that the supply voltage is OK.


Check: Are all plugs mounted correctly on the TWINDRIVE TD3? 

Try/Solution: Check all connections. Use the cable relief on the TD3 to make sure the cable does not fall out. Follow the procedure shown in the video or the instructions below.

The neck function of the bed does not work; it cannot drive outwards

The actuator adjusting the neck function needs to be initialized. Follow the instructions shown in the video or in the following steps:

TD3 AND LA27 - How to initialize the motor system

  1. Push the down button on the actuator.
  2. Drive the actuator until it has reached the inner position and stops completely.
  3. Release the key on the handset.
  4. Reactivate the down key on the actuator and keep it activated for approx. 5 sec.
  5. You can now drive the actuator outwards.

The system has now been initialized.

Got a question about electric actuator technology?

- Our team is ready to assist you with technical information, starting a project and more.

Subscribe to LINAK news

Stay informed about how actuator technology follows the megatrends of today and meets the global challenges of tomorrow