HC30 wireless

How to assemble a single actuator system

The system consists of:
Single actuator(s)
1 x Switch Mode Power Supply
1 x CBH Advanced
1 x Bluetooth^® hand control
1 x Bluetooth^® Adapter

1. Connect single actuators in channels 1-2 to control adjustment of, for example, backrest and leg support. (With the 3-ch CBH Advanced, the 3rd channel can also be used for an actuator)
2. Plug the DC cable into the CBH Advanced
3. Plug the Bluetooth^® Adapter into the CBH Advanced
4. Connect to a power outlet
5. Pair the hand control (press the two top buttons simultaneously)
6. The system is now ready for setup

To watch our videos, please accept marketing cookies

How to connect a system with the TD4 Advanced and the CBH Advanced

The system consists of:
1 x TD4 Advanced
1 x Switch Mode Power Supply
1 x CBH Advanced
1 x 2-poled DC cable
1 x Serial cable
1 x Bluetooth^® hand control
Single actuator(s)
2 x screws

1. Place the CBH Advanced onto the TD4 Advanced & use two screws to fasten it
2. Plug the serial cable into the TD4 Advanced and channel A1 on the CBH Advanced
3. Plug a 2-pole DC cable into the TD4 Advanced and channel DC on the CBH Advanced
4. Connect the SMPS to the TD4 Advanced
5. Connect single actuators in channels 1 and 2 for adjustment of, for example, the neck rest and foot rest.
6. If needed, connect massage motors in channels 3A and 3B
7. Connect to a power outlet
8. Pair the hand control (press the two top buttons simultaneously)
9. The system is now ready for setup

To watch our videos, please accept marketing cookies

Learn how to pair wireless hand controls to the LINAK^® single actuator LA18 IC system for comfort beds using Bluetooth^® technology.

1. Connect the system to a power outlet
2. Pairing mode has started when the Under Bed Light starts flashing. It will run for 3 minutes
3. Press the top two buttons to pair the hand control 
4. A long flash means successful pairing
5. The system is paired and ready for use
6. The system will continue to be in pairing mode until the previously mentioned 3 minutes elapse. Then the light will turn green continuously to show that the system is no longer in pairing mode

To watch our videos, please accept marketing cookies

How to store memory on a hand control

1. Adjust the bed to a preferred position
2. Press S and then choose the number on which you want to store the position
3. Now the position is stored
4. When you want to return to this position later, simply press and hold the button on which you stored the position

To watch our videos, please accept marketing cookies

How to initialize a single actuator system

1. Connect to a power outlet
2. Actuators must be in the inner position
3. Push the "down" button of the actuator on the hand control for approx. 5 seconds
4. The actuator now initiates and can drive outwards
5. Repeat this for each actuator by pressing the matching "down" button on the hand control
6. The actuator system is now initialized

To watch our videos, please accept marketing cookies

If you need a new hand control for your adjustable bed, you need to contact the supplier from whom you purchased the bed. 
This applies both in cases where you have lost your hand control, the hand control is broken as well as in cases where the battery has run out of power and the battery cannot be exchanged. The supplier will assist you in ordering a new hand control - LINAK does not sell spare parts directly to the person who owns the bed.

The LINAK hand control for an adjustable bed does not work

If you experience problems with the hand control for your adjustable bed, you need to contact the supplier from whom you purchased the bed. 
LINAK does not sell spare parts directly to the person who owns the bed.

How to pair hand controls to a system with a CBH Advanced and a Bluetooth^® Adapter

1. Connect to a power outlet  
2. Bluetooth^® Adapter flashes for 3 minutes to indicate pairing mode
3. To pair a hand control, press the two top buttons while the adapter is flashing
4. A long flash indicates successful pairing
5. All LINAK hand controls are paired by pressing the two top buttons

How to pair a hand control later

1. Start pairing mode again
2. Unplug from the power outlet and wait 10 seconds
3. Connect to a power outlet
4. Bluetooth^® Adapter flashes for 3 minutes to indicate pairing mode
5. Repeat pairing procedure on the other hand control
6. The system is now paired and ready to use

To watch our videos, please accept marketing cookies

How to connect a TD4/TD5 Advanced system and use parallel drive

The system consists of:
2 x TD4/TD5 Advanced
2 x Switch Mode Power Supply
1 x Serial cable
1 x Bluetooth^® hand control 

1. Connect 2 x SMPS to the 2 x TD4/TD5 Advanced
2. Use one serial cable to connect the two TD4/TD5 Advanced
3. Connect both actuators to a power outlet
4. Pair the hand control
5. The TD4/TD5 system will now run in parallel when using the hand control

To watch our videos, please accept marketing cookies

1. Set the TD4 in pairing mode by connecting it to a power outlet.
2. The product is now in pairing mode. The Under Bed Light will blink to indicate this.
3. Take the Bluetooth hand control and press the Back “Up” and “Down” buttons at the same time. Now the light will display a long blink and indicate that the control and the actuator are paired up.

To watch our videos, please accept marketing cookies