Controls

HC05 wireless

The HC05 is a wireless handset control running on Bluetooth® technology. Ideal for TWINDRIVE actuator solutions in comfort furniture. Comes in high gloss white and a button to activate the Under-Bed Light.

Product description

HC05 wireless

The hand control HC05 is designed for use with TWINDRIVE® Bluetooth® based systems for leisure beds.The HC05 is a small hand control in the HOMELINE® product range. 

It comes in two versions; a glossy white version and a matt rubber black version. It combines ergonomic design and functionality into a user-friendly hand control with intuitive buttons without any annoying cable.

Product data sheet

HC05 Wireless data sheet

View the data sheet as an online magazine or download the PDF.

2D / 3D

Brochures & manuals

TWINDRIVE TD4 Advanced user manual

This user manual will tell you how to install, use and maintain your LINAK TWINDRIVE products.

TWINDRIVE TD4 wireless is the new standard

Explore the TD4, specially developed for comfort beds with a moderate need for power.

HOMELINE product overview

Explore the variety of TWINDRIVE systems with a low noise level and the small built-in dimensions used in both box spring beds and slatted beds.

TD4 quick guide - Pairing devices and mechanical lowering

Learn how it only takes a few steps to pair devices to the dual actuator TD4 using Bluetooth® technology or mechanically lower a comfort bed with TD4 in case of power shortages.

Support

Simultaneous drive with the TD4 Standard

How to set up a double bed for simultaneous drive with the TD4 Standard

The system consists of:
2 x TD4 Standard
2 x power cables
1 x Bluetooth® hand control

  1. Connect the two dual actuators TD4 to a power outlet
  2. The Under Bed Light on both TD4 dual actuators starts to flash to indicate pairing mode
  3. Pair the hand control (press the two top buttons simultaneously)
  4. A long flash indicates successful pairing
  5. Now both dual actuators TD4 Standard are paired to one hand control

Pairing hand controls to the CBH Advanced system with a Bluetooth® Adapter

How to pair hand controls to a system with a CBH Advanced and a Bluetooth® Adapter

  1. Connect to a power outlet  
  2. Bluetooth® Adapter flashes for 3 minutes to indicate pairing mode
  3. To pair a hand control, press the two top buttons while the adapter is flashing
  4. A long flash indicates successful pairing
  5. All LINAK hand controls are paired by pressing the two top buttons

How to pair a hand control later

  1. Start pairing mode again
  2. Unplug from the power outlet and wait 10 seconds
  3. Connect to a power outlet
  4. Bluetooth® Adapter flashes for 3 minutes to indicate pairing mode
  5. Repeat pairing procedure on the other hand control
  6. The system is now paired and ready to use
 

Buy a new LINAK hand control for an adjustable bed

If you need a new hand control for your adjustable bed, you need to contact the supplier from whom you purchased the bed. 
This applies both in cases where you have lost your hand control, the hand control is broken as well as in cases where the battery has run out of power and the battery cannot be exchanged. The supplier will assist you in ordering a new hand control - LINAK does not sell spare parts directly to the person who owns the bed.

The LINAK hand control for an adjustable bed does not work

The LINAK hand control for an adjustable bed does not work

If you experience problems with the hand control for your adjustable bed, you need to contact the supplier from whom you purchased the bed. 
LINAK does not sell spare parts directly to the person who owns the bed.

My LINAK hand control has run out of battery life

My LINAK hand control has run out of battery life

Unfortunately, for some hand controls it is not possible to change the batteries. If your battery in these hand controls runs out of power, you will have to purchase a new hand control. You can do this by contacting the vendor who sold you the bed. 

LINAK does not sell spare parts directly to the person who purchased the bed.

Pairing the TWINDRIVE TD4

With TWINDRIVE TD4 it is easy to connect a control or a mobile device with the LINAK Bed Control app.

TD3 - How to set up Bluetooth handsets

  1. Plug the Bluetooth Adapter into the powered up TD3.
  2. The Adapter is now in pairing mode. A blue blinking LED will indicate this.
  3. Take the Bluetooth hand control and press the Back “Up” and “Down” buttons at the same time. Now the light will display a long blink and indicate that the control and the actuator are paired up.

TD4 - How to set up a Bluetooth handset

  1. Set the TD4 in pairing mode by connecting it to a power outlet.
  2. The product is now in pairing mode. The Under Bed Light will blink to indicate this.
  3. Take the Bluetooth hand control and press the Back “Up” and “Down” buttons at the same time. Now the light will display a long blink and indicate that the control and the actuator are paired up.
 

Have a question about electric actuator technology?

- We are not psychics. But, we are experts in actuator technology. So do not hesitate to ask us anything about that.